Proof,
not promises.

Design validation, process capability and 100% electrical test are one system at PANAWIN — not three separate departments.

39 test capabilities 15 UL standards 9 certified systems
Electrical test lab with cable assemblies
100%
Electrical test on harness assemblies, with lot-level traceability

The quality system

Quality is designed in, then verified.

It begins with material selection and construction design. It continues through process capability studies, first-article inspection and 100% test. It does not end until the production reel performs like the sample.

39
In-house test capabilities
15
UL standards covered
100%
Harness electrical test
Ppk > 1.33
224G insertion loss

Four disciplines

One test floor. The full operating envelope.

Electrical, mechanical, environmental and material analysis sit together in-house. That means a failure can move from observation to root cause without leaving the building.

01 / Design

Design validation

Construction review, material selection, simulation and prototype testing against the application envelope.

02 / Process

Process capability

DOE, PFMEA, control plans and Ppk studies for critical characteristics, including high-speed SI.

03 / Test

100% electrical test

Continuity, withstand voltage, insulation resistance and application-specific test programs.

04 / Trace

Traceability

Lot-level records connect raw material, process parameters, test results and shipment.

Testing capability

Thirty-nine ways to find the problem first.

Our in-house test matrix covers the electrical, mechanical, environmental and material performance of cables and harnesses — from conductor resistance to six-axis robot dress-pack testing.

Electrical

  • High-frequency testing
  • Conductor resistance
  • Contact resistance
  • Thermal rise test
  • Smoke test
  • Current carrying test
  • Withstand voltage
  • Insulation resistance
  • Voltage drop
  • Withstand & partial discharge
  • Shielding transfer impedance
  • Harness test station

Mechanical

  • Dimensional measurement
  • Mechanical property
  • Tensile / pull-off / pressure
  • Insertion & extraction
  • Bending test
  • 3D torsion test
  • Torsion test
  • Flexure test
  • Drag chain test
  • Torsional test for wind
  • Six-axis robot harness test
  • Robotics dress-pack test

Environmental

  • Salt spray test
  • Constant temperature & humidity
  • Low temperature test
  • Low-temperature winding
  • Low-temperature tensile
  • Low-temperature impact
  • High-temperature test
  • Thermal cycling test

Material & other

  • Coating film thickness
  • Flame retardant test
  • Terminal cross-section
  • Waterproof test
  • Seal integrity test
  • RoHS tester
  • Infrared spectroscopy analysis

Measurement & management

Capability you can measure.

High-speed cable performance is only meaningful when it is measured at the right frequency, on the right sample size and over a full reel. Our lab is equipped for both development and serial qualification.

110 GHz
PNA measurement capability, including Keysight N5290A and R&D ZNA67EXT systems
67 GHz
PNA systems for high-volume SI verification and development
EDX + OGP
Material composition and optical dimensional analysis
125 / 140 GHz
Additional high-frequency capability for next-generation development

Equipment list reflects the high-speed cable laboratory. Additional electrical, mechanical and environmental test equipment supports the wider product portfolio.

Certification

Audited systems. Certified products.

Nine management-system and verification standards, plus a broad UL product-safety portfolio, support automotive, medical, industrial and data-center programmes.

ULProduct safety
UL listed and recognized cable, wire and harness constructions
ISO 9001Quality
Quality management system
ISO 14001Environment
Environmental management system
ISO 45001OH&S
Occupational health and safety
IATF 16949Automotive
Automotive quality management
ISO 13485Medical
Medical device quality management
ISO 50001Energy
Energy management system
ISO 27001Information
Information security management
ISO 37001Anti-bribery
Anti-bribery management system
ISO 14064GHG
Greenhouse gas verification
IPC membership

Standards-led assembly discipline.

PANAWIN is a member in good standing of IPC, supporting the cable and harness assembly standards that customers rely on.

High-voltage qualification

Qualified for high-voltage installation.

Our teams hold high-voltage cable jointer and installation qualifications for demanding energy and infrastructure programmes.

UL portfolio

Coverage across cable, wire and assemblies.

Fifteen UL standards underpin our product-safety coverage for industrial, automotive, data-center, photovoltaic and appliance applications.

UL758Appliance wiring material
UL2263Electric vehicle cable
UL1063Machine-tool wire
UL62Flexible cords and cables
UL467Grounding and bonding equipment
UL4703Photovoltaic wire
UL1277Power-limited circuit cable
UL444Communications cable
UL13Power-limited circuit cable
UL817Wiring harnesses
UL1650Portable power cable
UL1072MV-90 and MV-105 medium-voltage cable
UL2137Data-center power cable
UL83Thermoplastic-insulated wire
UL2238Cable assemblies for industrial control and signal distribution

Production qualification

224G capability, proven over a full reel.

Duration study and process-capability study for SI, length > 1,500 ft (one full reel), 32 pieces. Tape dimension, structure, overlap and lay length verified within specification on 16 pieces.

Ppk > 1.33
Insertion loss at Nyquist frequency
100%
SDD11 / SDD22 pass, no spike
100%
SCD21 and SCD21–SDD21 pass
100%
ILD pass